Moog Videolarm QFDWT4-70NA Spezifikationen PDF herunterladen

ELECTRICAL SPECIFICATIONS (OUTDOOR ON LY):

Power 24VAC, Class 2 Only

26 watts at 24 VAC (accessories)

Heater: 25 watts

Blower: .84 watts

Input Connectors (outdoor units):

BNC Connectors - 1 for each camera

Screw-down connectors - 2

NOTE: This unit is designed for operation in an

upright position. Installing the Fusionome™

upside down may cause damage to the

internal equipment, and will void the warranty.

P R ODUCT INST RUCTIONS

REVISION DATE : 02-02-2009

81-IN5247-07064 Q-View FusionDome

QF DW(T/C)X-XXXX / QIFDW(T/C)X-XXXX

CAMERAS VOLTAGE CURRENT POWER

1 24 VAC/VDC 102mA 2.5W

2 24 VAC/VDC 210mA 5W

3 24 VAC/VDC 331mA 7.9W

4 24 VAC/VDC 487mA 10.9W

Use the formula below to select the correct power supply for

cameras connected in parallel (positive to positive, negative to

negative):

Total current for a 24 V AC system:

TO TAL CURRENT = (202mA x total number of cameras)

Note: 202mA is camera plus power supply

CABLE AND P OWER GUIDELINES (Detailed in fo on P age 12)

This chart shows the proper current needed for power supplies for

Q-View™ cameras. Use Class 2 Power only. Input voltage must

be 24 VAC/VDC.

3. Pull the wires from the wall through the rectangular hole in the

wall mount bracket. Attach the wall mount to the wall using

appropriate hardware (not included).

4. Make all wiring connections (See next page). Attach the BNC

connectors to the video in.

5. Once all wiring connections are made, place the wires inside the

wall mount bracket and close the access door. Secure with the

screw removed earlier.

WALL MOUNTING THE QFD

1. A template is included as a guide for mounting the bracket to a

wall. Choose the desired location for installation and mark the

drill holes using the template. Run approximately 8"of wiring out

of the wall.

2. Open the access door on the bottom of the wall mount by

loosening the screw nearest the mounting plate (Figure 1).

Figure 1

Access door

GENERAL INST R UCTIONS:

Tools Required: .100" Flat Head Screwdriver

Phillips Head Screwdriver

Carefully remove the housing from the packaging material. Check to

be sure all parts are present.

TABLE OF CONTENTS

Ca ble and Power Guidelines 1, 11

Electrical Speciﬁcations 1

General Instructions

Wall Mounting 1

Pendant Mounting 2

Wiring 2

Camera Adjustment 2

Camera Focusin g 2

Camera Settings 3

Completion of Installation 3

NVT Instructions 4

Exploded View 6

Warranty Information 7

Se rvice and Safeguard Information 8

Troubleshooting 9

Mounting Template 12

PEN DANT MOUNTING THE QFD AND QIFD

1. This unit includes a 1 1/2" NPT housing coupling that can be used

with a standard 1 1/2" NPT pipe or with brackets designed with

1 1/2" male pipe threads, such as Videolarm's WM20G.

2. Attach the coupling to the bracket or pendant pipe (Figure 2).

NOTE: Pipe threads should be clean and rust free. Use a

sealer (such as Teﬂon™ tape or silicone sealer) on the

threads for outdoor applications

Be sure the bracket is properly and securely mounted to a

supporting structure capable of rigidly holding the weight of

the entire unit.

Figure 2

Add thread

sealing tape

1 2 3 4 5 6 ... 11 12

Inhaltsverzeichnis

Seite 1 - P R ODUCT INST RUCTIONS

!!ELECTRICAL SPECIFICATIONS (OUTDOOR ON LY): Power 24VAC, Class 2 Only 26 watts at 24 VAC (accessories)Heater: 25 watts Blower: .84 wa

Seite 2

- 11 -Use the formula below to select the correct power supply for cameras connected in parallel (positive to positive, negative to negative):Total cu

Seite 3

- 12 -Mounting Template2.0003.250R .7332.1322.9811.5375.500

Seite 4 - NVT INSTRUCTIONS

Product Registration/WarrantyThank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highes

Seite 5 - Wiring Notes

- 2 -Figure 3Twist and SecureWIRING1. Attach the incoming power and accessory wiring using the color code chart below.1 Camera Power (2

Seite 6 - EXPLODED VIEWS OF HOUSING

- 3 -The operational settings for the camera are deﬁned by ten dip switches located on the PC Board (Figure 9). Moving the switches to the on position

Seite 7 - 1-800-554-1124

- 4 -NOTE: This hi-res color camera uses a 1/4" chip and a 3-6mm auto iris lens. It is comparable to a 1/3" chip using a

Seite 8 - TROUBLESHOOTING

- 5 -!!250 ft3 4 5 8 13 1300 ft4 5 6 10 16 1400 ft5 6 8 13 21 1500 ft6 8 10 16 26 1600 ft8 10 12 19 31 1800 ft10 13 16 25 42 11000 ft13 16 20 32 52 1

Seite 9 - NVT TROUBLESHOOTING

- 6 -2827262524232221201918173331323029161571312111098765432117 1/4 x 20 FH SS Bolt 90-BTSR01 1 18

Seite 10 - CABLE AND POWER GUIDELINES

! CAUTIONRISK OF ELECTRIC SHOCK! CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE COMPONENTS TO WATER OR MOISTURE.SAFETY PRECAUTIONS

Seite 11 - Mounting Template

- 9 -Power SupplyPower APower BCamera AssemblyPrimaryPowerVideo SignalVideo ShieldMonitor(Ground Return)Figure A Ground LoopTROUBLESHOOTINGIf you expe

Seite 12 - Online Option 2: Mail-In

- 10 -AC VoltmeterCamera MonitorBridge TapNV-213ANV-213ANVT TROUBLESHOOTINGIf you are experiencing problems, attempt to simplify your setup. Test each

Kommentare zu diesen Handbüchern

Keine Kommentare

Moog Videolarm QFDWT4-70NA Spezifikationen

Stöbern Sie online oder laden Sie Spezifikationen nach Sicherheitskameras Moog Videolarm QFDWT4-70NA herunter. Moog Videolarm QFDWT2-70NA surveillance camera Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitskameras Moog Videolarm QFDWT4-70NA