Moog Videolarm QODT4-70NA Spezifikationen PDF herunterladen

- 1 -

GENERAL INSTRUCTIONS

1. Remove contents from the box.

2. Remove the existing ceiling tile from the desired location.

3. Insert the loose end of the saftey cord on the dome through the

middle hole on the edge of the housing opening (Figure 1).

Figure 1

4. Align the eyelet on the cord with the hole located on the inside of

the housing tile opening.

5. Insert the 6-32 x 1/2 round Phillips head screw through the

hole and eyelet. Place the star lockwasher and 6-32 hex nut on

the screw and tighten.

6. Fit the 2 x 2 housing tile in the desired location. The housing

tile will rest on the ceiling grid. (Be sure the grid is adequately

supported).

Safety Cord

goes here

PRODUCT INSTRUCTIONS

REVISION DATE: 02-02-2009

81-IN5257-07024

QOD Q-View ObservaDome

QOD(T/C)X-XXXX

CAMERAS VOLTAGE CURRENT POWER

1 24 VAC/VDC 102mA 2.5W

2 24 VAC/VDC 210mA 5W

3 24 VAC/VDC 331mA 7.9W

4 24 VAC/VDC 487mA 10.9W

Use the formula below to select the correct power supply for

cameras connected in parallel (positive to positive, negative to

negative):

Total current for a 24 VAC system:

TOT AL CURRENT = (202mA x total number of cameras)

Note: 202mA is camera plus power supply

CABLE AND POWER GUIDELINES (Detailed info on Page 10)

This chart shows the proper current needed for power supplies for

Q-View™ cameras. Use Class 2 Power only. Input voltage must

be 24 VAC/VDC.

WIRING

1. Make the proper connections to the incoming power. The RED

wire is POSITIVE (+), the BLACK wre is NEGATIVE (-) (For refer-

ence purposes. Polarity is not important in this unit). The GREEN

wire, labeled Ground, is GROUND for VAC or VDC connections.

NOTE: Connect green ground wire to earth ground (metal conduit,

metal stud, etc.)

2. Attach the BNC connectors to the video in.

TA BLE OF CONTENTS

Cable and Power Guidelines 1, 10

cations 1

General Instructions 1

Wiring 1

Camera Adjustment 1

Camera Focusing 1

Camera Settings 2

Completion of Installation 4

NVT Instructions 4

Wa rranty Information 6

Service and Safeguard Information 7

Tr oubleshooting 8

CAMERA ADJUSTMENTS

1. After completing installation of the housing, use the segmented

arms to adjust each camera to the desired viewing location.

2. Once camera adjustments are made, place the dome back into

position to be sure cameras are not touching the inside of the

dome. If any do, adjust until they are clear.

CAMERA FOCUSING

1. Fine focusing:

Fixed Lens: Loosen the set screw in the lens mount and

manually rotate the lens until a clear picture is achieved. Once

the focus is set, retighten the set screw (Figure 2).

Figure 2

Set screw

Fixed lens

1 2 3 4 5 6 7 8 9 10

Inhaltsverzeichnis

Seite 1 - PRODUCT INSTRUCTIONS

- 1 -GENERAL INSTRUCTIONS1. Remove contents from the box. 2. Remove the existing ceiling tile from the desired location. 3. Insert the loose e

Seite 2 - CAMERA SETTINGS

Product Registration/WarrantyThank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highes

Seite 3

- 2 -CAMERA SETTINGSSERIAL NUMBERS BEGINNING WITH YKFIXED AND FIXED VARI-FOCAL LENSES. There are no user adjustable settings on these units (Figure 4)

Seite 4 - NVT INSTRUCTIONS

SWITCH SETTING DEFINITIONFlickerless Mode1 Setting this switch to "On" and switch 3 (MIRIS) to "Off&q

Seite 5

- 4 -!!NVT INSTRUCTIONSUNSHIELDED TWISTED PAIR VIDEO WIRINGNOTE: The customer must purchase the Video Transceiver from NVT. Part number

Seite 6 - 1-800-554-1124

- 5 -250 ft 250 ft 3 4 5 8 13 Ω300 ft 300 ft 4 5 6 10 16 Ω400 ft 400 ft 5 6 8 13 21 Ω500 ft 500 ft 6 8 10 16 26 Ω600 ft 600 ft 8 10 12 19 31

Seite 7 - TROUBLESHOOTING

! CAUTIONRISK OF ELECTRIC SHOCK! CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE COMPONENTS TO WATER OR MOISTURE.SAFETY PRECAUTIONS

Seite 8 - AC Voltmeter

- 8 -Power SupplyPower APower BCameraAssemblyPrimaryPowerVideo SignalVideo ShieldMonitor(Ground Return)Figure A Ground LoopTROUBLESHOOTINGIf you exper

Seite 9 - CABLE AND POWER GUIDELINES

- 9 -AC VoltmeterCamera MonitorBridge TapNV-213ANV-213ANVT TROUBLESHOOTINGIf you are experiencing problems, attempt to simplify your setup. Test each

Seite 10 - Online Option 2: Mail-In

- 10 -Use the formula below to select the correct power supply for cameras connected in parallel (positive to positive, negative to negative):Total cu

Kommentare zu diesen Handbüchern

Keine Kommentare

Moog Videolarm QODT4-70NA Spezifikationen

Stöbern Sie online oder laden Sie Spezifikationen nach Sicherheitskameras Moog Videolarm QODT4-70NA herunter. Moog Videolarm QODT4-70NA surveillance camera Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitskameras Moog Videolarm QODT4-70NA